manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 326 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 326

304

 GL-10x0 Administrator’s Guide

Cannot PING Controller

Problem Description

If the controller does not respond when you ping it, there is a problem 

either with the network configuration or with the operation of the 

controller.
The following checklist helps you identify the source of the error and 

directs you to where you can find more information about resolving it. If 

the problem persists after you have followed all of the steps, contact your 

TOSHIBA authorized dealer for further assistance.

6 Can another workstation 

within the same network 
segment discover the 
controller?

Next 
Step

’

‘

Network 

Connectivity 

Problems

 on 

page 298.

7 Check the startup page. Is 

the MAC address part of the 
device name?

Next 
Step

’

‘

Contact your 
TOSHIBA authorized 
dealer for support.

8 Check link activities on the 

port being used by the 
controller and the integrity of 
the network cable, hub, or 
switch that connects the 
controller to the network. 
Replace any network 
components that you can tell 
or suspect are faulty. 

End

‘

Device Discovery

Possible Cause

Check

Yes

No

For Instructions, 

Go To...

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments