Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 116

Page: 116 / 427

GL-10x0

Administrator’s Guide

As an administrator, you can:

View the status of the device and network

View and modify job queues

View and modify copier attributes

View accessory configuration

Scan

View the log files (counters)

The following is the TopAccess site map:

Device Tab
Print Jobs Tab

Current Subtab

Private Subtab

Proof Subtab

Scheduled Subtab

TopAccessComposer Subtab

Invalid Subtab

All Subtab

Fax Tab (GL-1010 only)
Scan Tab

Scan Jobs Subtab

Current Jobs

Job Log

Message Log

Templates Subtab

Templates

Template Groups

Download Scan Files Subtab

Preferences Tab
Counters Tab

Copy/Print Subtab

Routed Fax (GL-1010 only)

Scan Subtab

Administration Tab

Device Subtab

General

Copier

Printer

Version

Setup Subtab

Network

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 116 / 427

Search results

Summary of Contents for e-STUDIO GL-1010

Reviews: