Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 89

Page: 89 / 427

GL-10x0 Administrator’s Guide

Press

ELEASE

Enter the department code for the job or jobs you are releasing. If you

are releasing multiple jobs at the same time, all jobs must use the

same department code.

Entering the Department Code

The controller queues the job(s) for printing.

URGING

NRELEASED

IDC J

OBS

The controller purges unreleased IDC jobs according to the

Number of days

to save Private, Proof & Invalid Print Jobs

entry in TopAccess and recorded in the

jobs log.

ROCESSING

CCESS

OMPOSER

OBS

TopAccessComposer and TopAccessComposer Print jobs also require a

valid department code. If the code is invalid, the controller processes the

TopAccessComposer portion of the job normally and stores the document

in TopAccessComposer. It treats the Print portion of the job as an IDC job.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 89 / 427

Search results

Summary of Contents for e-STUDIO GL-1010

Reviews: