Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 233

Page: 233 / 427

GL-10x0 Administrator’s Guide

211

Page Setup and Page Attributes

Most of the printing options are accessible through the

Print

menu item,

which is typically under the

File

menu of the application or utility being

used.
General printer attributes are configured using the General section of the

CUPS Options page (page 209).

CUPS General Options

EDIA

IZE

Select the

Media Size

from the drop-down list.

CUPS Media Size Options

The supported paper sizes include:

Ledger

Legal

Letter

Statement

Folio

Computer

Legal 13

Letter Square

16K

, and

Postcard

If you are finished, click

Continue

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 233 / 427

Search results

Summary of Contents for e-STUDIO GL-1010

Reviews: