Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 340

Page: 340 / 427

318

GL-10x0 Administrator’s Guide

Latch the developer
unit

Latch the developer unit

Latch the developer unit.

Misfeed in finisher
(Press HELP)

Misfeed in finisher

Clear the misfeed in the finishing
unit. Press the copier HELP button
for more information.

Missfeed in copier
(Press HELP)

Missfeed in copier

Clear the missfeed. Press the
copier HELP button for more
information.

Missfeed in Inserter
(Press HELP)

Clear the missfeed in the inserter.
Press the copier HELP button for
more information.

Paper misfeed in
bypass

Paper misfeed in bypass

Clear the missfeed in the bypass
tray.

Please Dispose of Hole
Punch Dust

Dispose of hole punch dust

Dispose of the hole punch dust.

Remove paper from
saddle stitch unit

Remove paper from saddle
stitch unit

Remove paper from the saddle
stitch unit.

Service recommended
for IQC

Service recommended for IQC Service recommended for IQC.

Contact your TOSHIBA authorized
dealer for support.

Set key copy counter

Set key copy counter.

Set staple cartridge

Set the staple cartridge.

Set staple cartridge of
saddle stitch unit

Set staple cartridge of saddle
stitch unit

Set the staple cartridge of the
saddle stitch unit.

Time for periodic
maintenance

Time for periodic maintenance

Time for periodic maintenance.
Contact your TOSHIBA authorized
dealer for support.

USE GENUINE
TOSHIBA TONER

Use genuine TOSHIBA Toner

Check and adjust the toner bottle.

WAIT

Wait - Self maintenance

Please wait - Self maintenance in
progress.

Wait adding toner

Wait - Adding toner

Wait - Adding toner.

Message Log Error Messages (Continued)

LCD Message

TopAccess Message

Corrective Action

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 340 / 427

Search results

Summary of Contents for e-STUDIO GL-1010

Reviews: