Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 358

Page: 358 / 427

336

GL-10x0 Administrator’s Guide

Invalid IDS Code

Problem Description

An unknown Windows

String Resource

code was generated, so the

program is unable to supply a text description for the code.

Corrective Action

Restore the software from a reliable backup source or from the original

distribution CD-ROM.

TopAccess Error Conditions

Cannot Interpret Message Log Errors

Problem Description

The Message Log page displays the list of error, warning, and

informational messages generated by the controller. By selecting an

individual entry in the message log, you can view the information about

the record, including the

Date/Time

Severity

Subsystem

Description

Location

and

Data Path

Corrective Action

For a complete list of error messages, refer to the table

Jobs Log Status

Messages

on page 319.

Changes Made to the Controller Settings did not Take
Effect

Problem Description

Changes made to controller properties or copier attribute settings did not

take effect.

Corrective Action

Sometimes when you make changes to controller

settings from

TopAccess, you may have to reboot the controller for the changes to take

effect. When you change copier attributes, you must turn the copier off

and back on again for the changes to take effect. Shut down the

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 358 / 427

Search results

Summary of Contents for e-STUDIO GL-1010

Reviews: