manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 378 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 378

356

 GL-10x0 Administrator’s Guide

the queue. Banner pages are configured to print on either letter or A4 

sized paper only.

Corrective Action

1

No corrective action required.

2

Enable Banners through the Printer Settings dialog box.

3

Manually insert the correct media type at the copier.

Banner Page Listed as Separate Job in Queue

Problem Description

When you view the jobs queue from the copier LCD touch screen, two 

separate jobs are listed for one job sent.

Corrective Action

This is expected behavior. The banner page is sent as a separate print job 

so that output options applied to the print job are not applied to the 

banner page as well. Otherwise, the banner pages would be stapled to the 

remainder of the job, and multiple copies of a job would produce multiple 

copies of the banner page. In duplex printing, the banner page would be 

the first page with page 1 of the document printed on the back, and so on.
The banner page portion of the print job appears in the job list with 

Banner

 preceding the job name so that you can tell which job it is 

associated with.

Partial, Blank, or Blurry Pages

Blank Page Printed After Each Job

Problem Description

This results when the 

Form Feed

 option is enabled in the driver Printer 

Settings dialog box (Novell printing only).

Corrective Action

Deselect the 

Form Feed

 printer setting. If the problem persists, form feed 

may be enabled through the Novell network setup. Use NWAdmin to 

check the settings and modify them as necessary.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments