manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 332 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 332

310

 GL-10x0 Administrator’s Guide

Network print settings 
are not properly 
configured

6 Use the LCD touch 

screen to check that the 
printer is online and that 
the 

Protocol

 and 

Services

 

settings are set properly. 
Are the settings correct?

Next 
Step

’

‘

Refer to PART 3, 

Establishing 

Network Print 

Services

 on 

page 155. 

7 Reboot the controller and 

restart the copier for any 
changes to take effect. 
Resubmit the job and 
check the Current Jobs 
queue. Does the job 
appear in the list?

End

End

Rebooting the 

Controller

 on 

page 43.

Submitted Job Not in Current Jobs Queue (Continued)

Possible Cause

Check

Yes

No

For Instructions, 

Go To...

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments