manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 52 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 52

30

 GL-10x0 Administrator’s Guide

appropriate frame type. While this makes frame type discovery automatic, 

it can also cause network congestion.
1

From the Network Setting menu, press 

IPX

/

SPX

 to open the IPX/SPX 

Setting screen.

IPX/SPX Setting Screen

Note: The IPX/SPX Setting screen shown displays the Ethernet NIC 

settings.

2

If you are running a TCP/IP-only network, press 

DISABLE

. Otherwise, 

press 

ENABLE

 to accept or modify the IPX/SPX frame type.

3

Select the frame type from the options shown, 

EN_802.2

, 

EN_802.3

, 

EN_11

, 

or 

EN_SNAP

.

4

Press 

OK

 to save the changes.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments