Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 213

Page: 213 / 427

GL-10x0 Administrator’s Guide

191

Center Margin

Select the booklet mode center margin using the following option.

Example: The command to select the center margin value for booklet

printing mode is

lp –o centremargin=<value> <filename>

Outer Margin

Select the booklet mode outer margin using the following option.

Example: The command to select the outer margin value for booklet

printing mode is

lp –o outermargin=<value> <filename>

Inserter

When the inserter option is installed, you can activate it using this

function.

Booklet Mode Center Margin Option

Option Value

Description

centermargin=<

value>

Select the center margin value for booklet printing mode.

This value specifies in pixels the center margin or the

gutter

. This is

in addition to the center margin already specified by the application.
The valid range for <

value>

–

300

. The default is

Booklet Mode Outer Margin Option

Option Value

Description

Outermargin=<

value>

Select the outer margin value for booklet printing mode.

This value specifies, in pixels, the outer margin or the

creep

per page,

which should take place while printing a booklet. The valid range for
<

value

> is

–

. The default is

Inserter Options

Option Value

Description

insertpaper=LT

Selects Letter size paper for the inserter.

insertpaper=A4

Selects A4 size paper for the inserter.

insertpaper=LG

Selects Legal size paper for the inserter.

insertpaper=LD

Selects Ledger size paper for the inserter.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 213 / 427

Search results

Summary of Contents for e-STUDIO GL-1010

Reviews: