Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 54

Page: 54 / 427

GL-10x0 Administrator’s Guide

By default, Macintosh printing is enabled. If it has been disabled,

press

ENABLE

to establish Macintosh print services.

Press

APPLETALK

NAME

to display the touch keyboard.

Enter the AppleTalk name. The name is the same as the Microsoft

computer name (device name).
By default, the device name is GL<MAC Address>, where <MAC

Address> is the media access control number of the NIC installed in

the controller. For example,

GL00DOC9165206

. You can specify a

different name of up to 32 alphanumeric characters, provided it is

unique within your network.

Press

DESIRED

ZONE

to display the touch keyboard.

Enter the AppleTalk Zone, which is “*” by default. This indicates the

local zone, although you can specify a different name of up to 32

alphanumeric characters.

Press

to save your changes.

Naming the Device and Workgroup

From the Admin menu, press

ETWORK

SETTING

to open the Network

Setting screen.

Device Setting Screen

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 54 / 427

Search results

Summary of Contents for e-STUDIO GL-1010

Reviews: