manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 343 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 343

GL-10x0 Administrator’s Guide

321

Scan-Related Error Messages

Unserviceable, Paper Not 
Loaded (UNIVERSAL)

Out of paper.

Load Paper (UNIVERSAL) 
according to the instructions on 
the copier control panel LCD.

Unserviceable, Paper Out

Out of paper.

Load Paper according to the 
instructions on the copier 
control panel LCD.

Unserviceable, PJL Error

Conflicting or incorrect 
driver settings.

Review the print properties 
selected for the job. For more 
information, refer to 

Troubleshooting Output 

Errors

 on page 349.

Scan-Related LCD Messages

Message

Corrective Action

100 sheets can be set on the ADF. 
To continue, repeat the operation.

The number of sheets in the ADF has reached the 
maximum (100). Reduce the number of pages and try 
scanning again

Finish ADF Scan 

Place a document on the ADF.

Finish glass Scan (A document is on 
ADF)

A document on the glass is being scanned. Wait until 
the current scan process is complete before using the 
ADF scan function.

Finish glass Scan (Job full)

The amount of data has reached the maximum. 
Reduce the resolution or change the document type to 

Text

 or 

Text/Photo

 and try scanning again. 

Finish glass Scan (Max page 
reached)

The number of pages has reached the maximum (200) 
pages. Finish the current page and retry scanning the 
remaining pages. 

Invalid Group Password

Enter the correct group number and/or password. 

Jobs Log Status Messages (Continued)

Message

Cause

Corrective Action

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments