manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 354 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 354

332

 GL-10x0 Administrator’s Guide

Unknown Controller Network Settings

Problem Description

There are several ways you can check or change the current network 

settings configured for the controller:

„

Print a configuration page from the copier control panel. Refer to 

Printing Test Pages

 on page 43 for instructions.

„

Access the protocol and device settings from the copier control panel. 

Refer to 

Modifying Protocol Settings Locally

 on page 26.

„

Use the embedded web-based administration utility, TopAccess, to 

view current network settings. Refer to the TopAccess Help for 

instructions. 

Network Problems

7 Are other services and 

communications performed 
over the network behaving 
in the normal and expected 
manner? 

Next 
Step

’

‘

Refer to your network 
documentation or use 
a network diagnostic 
utility to research a 
network problem.

Cannot Print to the Controller

Possible Cause

Check

Yes

No

For Instructions, 

Go To...

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments