manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 335 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 335

GL-10x0 Administrator’s Guide

313

The following checklist helps you identify the source of the error and 

directs you to where you can find more information about resolving it. If 

the problem persists after you have followed all of the steps, contact your 

TOSHIBA authorized dealer for further assistance.

Troubleshooting Checklist

Device Name Does Not Default

Problem Description

The first time the controller is powered on, it detects the MAC address of 

the installed NIC, from which it derives the default device name, 

GL<

MACaddress

>. However, if you have reason to install a new NIC in the 

Starting Controller, Please Wait

Possible Cause

Check

Yes

No

For Instructions, 

Go To...

Unsynchronized 
communication 
between the 
controller and the 
copier

1 Reboot the controller. 

Please be patient. It can 
take several minutes for 
the controller and copier to 
fully initialize and 
commence communication. 
When the system comes 
back online, is the 

Starting Controller, 
Please Wait

 or 

Shut-

down in Progress, 
Please Wait

 message 

still displayed?

Next 
Step

’

End

TopAccess online 
Help.

Corrupt controller 
software

2 Use the 

e-STUDIO 

Recovery CD-ROM

 to 

restore required system 
files. When the system 
comes back online, is the 

Starting Controller, 
Please Wait

 or 

Shut-

down in Progress, 
Please Wait

 message 

still displayed?

Call

End

See the field service 
guide.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments