manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 252 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 252

230

 GL-10x0 Administrator’s Guide

Installing Windows Software

The client software includes the TopAccessDocMon print job monitoring 

utility, printer drivers for PCL and PostScript (PS), the GL TWAIN Driver, 

and the AGFA Font Manager.

Considerations and Limitations

„

The TopAccessDocMon utility monitors only GL-1020, GL-1010, and 

SC-2 devices. It does not support any third party printer drivers. 

TopAccessDocMon cannot locate or interrogate the controller if it has 

been set up as a NetWare NDPS printer or NPRINTER.

„

You must install a printer driver and map it to the controller to access 

it using TopAccessDocMon.

„

You can view all jobs in the print queue, including controller-resident 

jobs, but can only delete your own jobs.

Prerequisites

Make sure that the client workstation meets the following minimum 

requirements:

„

Windows

 

98

„

Novell Client v3.4 or higher and Client Service Pack 1 are 

required to run IPX-based SNMP access and Novell printing.

„

The Microsoft Client for NetWare can replace the Novell Client 

except for NDPS printers.

„

Windows Me

„

Novell Client v3.4 or higher is required to run IPX-based SNMP 

access and Novell printing.

„

The Microsoft Client for NetWare can replace the Novell Client 

except for NDPS printers.

„

Windows NT 4.0

„

Microsoft Service Pack 6A or higher

„

Novell Client v4.9 SP1a or higher with Z.E.N works Starter Pack 

and Service Pack 1 are required to run IPX-based SNMP access 

and Novell printing.

„

The Microsoft Client for NetWare can replace the Novell Client 

except for NDPS printers.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments