manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 211 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 211

GL-10x0 Administrator’s Guide

189

Department Code

Set the department access code using the following option.

Booklet Modes

The booklet mode can be selected using the following options.

If this value is LT and the paper size in the printer description language 

(PDL) is also LT paper size, the resulting booklet is scaled to fit on letter 

sized paper. If this value is A3 and the paper size in the PDL is A4, then 

the resulting booklet is a tiled booklet on A3 sized paper.

Department Code Option

Option Value Description

Dept=

code

Sets the department access code. The 

code

 

is a 5-digit numeric value.

Booklet Mode Options

Option Value

Alternate Value Description

Booklet= letter

lt, LT

Select letter size paper for booklet printing mode.

Booklet=A4

a4

Select A4 size paper for booklet printing mode.

Booklet= legal

lg, LG

Select legal size paper for booklet printing mode.

Booklet= statement

st, ST

Select statement size paper for booklet printing 
mode.

Booklet= ledger

ld, LD

Select ledger size paper for booklet printing mode.

Booklet= folio

folio-japan

Select folio size paper for booklet printing mode.

Booklet= A3

a3

Select A3 size paper for booklet printing mode.

Booklet= A5

a5

Select A5 size paper for booklet printing mode.

Booklet= B4

b4, B4-JIS, b4-jis

Select JIS B4 size paper for booklet printing mode.

Booklet= B5

b5, B5-JIS, B5-jis

Select JIS B5 size paper for booklet printing mode.

Booklet= computer

co, CO

Select computer size paper for booklet printing 
mode.

Booklet= legal13

lg13, LG13

Select legal-13 size paper for booklet printing mode.

Booklet= SQ85

sq85, letter-square

Select 8.5 inch square size paper for booklet 
printing mode.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments