manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 350 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 350

328

 GL-10x0 Administrator’s Guide

Cannot See the Controller

Problem Description

After installing and configuring the controller, you cannot see it on the 

network. This could be the result of controller problems, but is more likely 

to be caused by network configuration errors.
The following checklist helps you identify the source of the error and 

directs you to where you can find more information about resolving it. If 

the problem persists after you have followed all of the steps, contact your 

Toshiba authorized dealer for support.

Troubleshooting Checklist

Cannot Find the Controller

Possible Cause

Check

Yes

No

For Instructions, 

Go To...

Controller is 
initializing and is not 
online yet

1 Did a startup page print out? 

If not, wait until the controller 
comes online. Examine the 
protocol settings that print 
out on the startup page. Are 
they correct?

Next 
Step

’

‘

Modifying Protocol 

Settings Locally

 on 

page 26.

Controller is down

2 Are any error messages, 

such as 

Starting 

Controller. Please 
Wait.

 displayed on the 

copier control panel?

‘

Next 
Step

’

Starting 
Controller, 
Please Wait

 or 

Shut-down in 
Progress, Please 
Wait

 Message 

Appears

 on 

page 312.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments