Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 347

Page: 347 / 427

GL-10x0 Administrator’s Guide

325

Incompatible OS Message

Problem Description

During a controller software update, the following message screen is

displayed:

Incompatible OS Message Screen

Corrective Action

Press

Yes

to update the operating system software. If you do not have

the latest version, contact your Toshiba authorized dealer for support.

Refer to the field service guide for instructions on updating the

controller operating system.

After completing the operating system update, retry the controller

software update. Refer to the field service guide for instructions.

Indeterminate, Unexpected Behavior

Problem Description

If the copier behaves in a way that is unexpected and cannot be explained

or resolved, the copier firmware (FROM) may conflict with, or does not

support, the currently installed version of the controller software.

Anything from features becoming unavailable to complete system seizure

could indicate that this is the problem.

Corrective Action

If you suspect this is the case, contact your TOSHIBA authorized dealer

for further assistance.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 347 / 427

Search results

Summary of Contents for e-STUDIO GL-1010

Reviews: