manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 67 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 67

GL-10x0 Administrator’s Guide

45

Controller Software Recovery Update

Replaces the operating system (OS) software and the controller software 

from the bootable 

e-STUDIO Recovery CD-ROM

.

There are two ways to update the operating system:

„

Boot the controller from the 

e-STUDIO Recovery CD-ROM

.

„

Perform an 

OS U

PDATE

 from the copier control panel. This is the 

recommended method of updating the OS software. The controller 

performs a backup operation and saves the administrator password, 

network settings, scan templates, address book, and other settings 

which are then restored following the update.

This section provides procedures for performing each method of operating 

system update.

Update from the 

e-STUDIO Recovery CD-ROM

1

Power up the system if it is not already running.

2

Immediately insert the 

e-STUDIO Recovery CD-ROM

 into the drive. If 

the controller was already up, reboot it. The flashing light on the 

CD-ROM drive indicates the controller is trying to boot off of the CD. 

If this light does not flash, leave the CD in the drive and reboot the 

controller.

3

Check the LCD touch screen on the copier. It displays the following 

message as the controller boots off of the CD-ROM: 

Starting 

controller. Please wait.

4

When the controller finishes booting up, a process that takes almost 

three minutes, the 

Offline OS Update Version

 screen opens:

The Offline OS Update Version Screen

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments