manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 130 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 130

108

 GL-10x0 

Administrator’s Guide

PJL jobs from printer drivers. Raw jobs are sent to port 9100 if no LPR 

queue is specified. The controller does not support raw jobs sent to any 

other port.
Differences between the built in queues:

„

DSSC: This is the only built-in queue that supports fax. If installing 

the printer driver via Point-And-Print, double-clicking this queue 

name downloads the PCL6 printer driver

„

DSSCTAC: This is an LPR queue and cannot be browsed from 

Windows. Any print job sent to this queue will be redirected to 

TopAccessComposer. It can be used from a Unix system or a Windows 

system as long as the printer uses a standard TCP/IP port.

„

GL_PS: If installing the printer driver via Point-And-Print, double-

clicking this queue downloads the PS printer driver

„

GL_PCL6: If installing the printer driver via Point-And-Print, double-

clicking this queue downloads the PCL6 printer driver

Any print job (PCL or PS) can be sent to any of these queues.
Each of these queues also has the following properties:

„

Queue Name

„

Duplex Printing: Enable/disable

„

Paper Size: Ledger, legal, letter, computer, statement, A3, A4, A5, B4, 

B5, folio, 13-inch legal, 8.5-inch square, 8K, and 16K

„

Paper Type: Transparency, plain, tab paper, thick1, thick2, cover, 

insert, special

„

Orientation: Portrait or landscape

„

Stapling: On or off

„

Output Tray: Tray 1 or tray 2

„

Points per line

„

PCL Font Pitch

„

PCL Font point Size

„

PCL Font Number

„

Banner Page: Enable/disable

To set raw job options:
1

Log in as an administrator.

2

Click the 

Administration

 tab.

3

On  the 

Device

 subtab, click 

Printer

. The Print Settings page opens.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments