manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 200 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 200

178

 GL-10x0 Administrator’s Guide

Installing the Unix TAR File

Considerations and Limitations

„

This print model acts only as a filter and not as a complete driver. You 

cannot modify the size and order of the printed pages.

„

The UNIX filters do not support the following engine-supplied 

features:

„

Magazine Sort

„

Saddle-stitch

„

N-Up

„

Watermarks

„

Cover Sheets

„

Sheet Insertion

„

You must have root privileges to install the required files.

„

Linux uses the 

lptap

 command to send a file to a printer. Since 

lp

 is 

not supported in all versions of Linux, use the 

lptap

 command 

instead.

„

AIX supports printing using the 

qdaemon

. Invoke this daemon with 

the commands 

lp

, 

lpr

, or 

qprt

. To use the GL filter, use either 

lp

 or 

qprt

.

Supplied Components

Many of the files described in this section vary slightly between the 

GL-1010 and the GL-1020 controllers. Make sure you select the correct 

files and place them in the correct directories for the appropriate 

controller.

„

net_gl10X0

: This file is a shell script installed in 

/usr/lib/lp/

model/net_gl10X0

. It contains the parsing data for the controller 

specific commands and generates the output code. Being a shell 

script, a system administrator can modify it, if a site requires any 

custom options or if other components are installed in non-standard 

locations.

„

lpdsend

: This is an executable program called by 

net_gl10X0

 to 

send the print file to the controller using the LPD protocol. This 

program is installed in 

/opt/toshiba/tap/bin/lpdsend

.

„

lpLinux.sh

 (Linux filter only): This file is a shell script that simulates 

the command line functions of 

lp

.  After processing the command line 

options, the GL filter is invoked in the same way as a System V print 

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments