Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 190

Page: 190 / 427

168

GL-10x0

Administrator’s Guide

Select the

NDPS Gateway Printing Mechanism

LPR on IP

Remote Printer on IPX

Queue-Based (NDS Printer Agent)

Click

Next

. The configuration dialog box that opens depends on the

printing mechanism you choose. See

LPR Printer Agent

on page 168,

Remote Printer on IPX

on page 169, or

Queue-Based

on page 170.

When you finish configuring the printer agent, proceed to

Select

Drivers

on page 171.

Note: After you create the printer agent, Wait a minimum of 60

seconds (preferably 90 seconds) before accessing the printer details.

Accessing the details early may result in the display of an incorrect

icon depicting the printer configuration.
Note: If you change the copier configuration after completing the

initial set up and configuration (i.e. you remove the finisher), You

must either reboot the NetWare server or create a new printer agent to

reflect the change configuration.

LPR Printer Agent

If you select the

LPR Gateway

configuration option, the TOSHIBA

Remote-LPR Printer Configuration dialog box opens:

TOSHIBA Remote-LPR Printer Configuration Dialog Box

Enter the

IP Address

of the controller and then click

Finish

To confirm your choice, click

Yes

When the update is complete, proceed to

Select Drivers

on page 171.

Configure the controller for LPR/LPD printing to use this service.

(Refer to

LPR/LPD Printing

on page 175.)

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 190 / 427

Search results

Summary of Contents for e-STUDIO GL-1010

Reviews: