manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 324 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 324

302

 GL-10x0 Administrator’s Guide

Cannot Discover Device

Problem Description

Controllers are discovered automatically using SNMP. When 

TopAccessDocMon cannot automatically discover an installed controller 

over the network, the most likely cause is limitations of the protocols on 

the supporting workstations. In some cases, you need to add or update 

network components.

Macintosh 
Environment

• AppleTalk and TCP/

IP protocols

• Peer to Peer net-

working

• Clients running on 

the Macintosh plat-
form

1 Is AppleTalk enabled on 

the controller?

Next 
Step

’

‘

Configuring 

AppleTalk

 on 

page 224.

2 Is TCP/IP set up on the 

controller?

Next 
Step

’

‘

Configuring TCP/IP 

Protocol Settings

 on 

page 28.

3 Is the controller 

available in the Chooser 
(MacOS 9.2.2+) or the 
Print Center (Mac OS 
10.2.6+) when you click 
on the LaserWriter 
8.6.5+ printer icon?

Next 
Step

’

‘

Make sure the 
AppleTalk zone is 
supported by the 
Macintosh client.

4 Can you access any 

other network device 
from the Macintosh 
workstation?

Next 
Step

’

‘

Refer to your Macintosh 
networking 
documentation or 
contact Macintosh 
technical support. 

5 Can another Macintosh 

workstation on the 
network print to the 
controller? If so, 
compare the settings to 
determine which need to 
be changed to support 
printing from this 
machine. 

End

‘

Refer to your Macintosh 
networking 
documentation or 
contact Macintosh 
technical support. 

Resolving Network Connectivity and Printing Issues (Continued)

Network 

Configuration

Check...

Yes

No

For Instructions, 

Go To...

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments