manualshive.com logo in svg

Mitsubishi Electric MR-J4W2-0303B6, Instruction Manual

The Mitsubishi Electric MR-J4W2-0303B6 is a cutting-edge product designed to deliver precise and efficient performance. For users in need of guidance, an easy-to-understand Instruction Manual is available for free download at manualshive.com. Unlock the full potential of this exceptional product with our comprehensive manual.

Share
Download
background image

17. APPLICATION OF FUNCTIONS 

17 -  39 

 

(c)  Caution for one-touch tuning 

1)  Caution common for user command method and amplifier command method 

a) The tuning is not available in the torque control mode. 

 

b) The one-touch tuning cannot be executed while an alarm or warning which does not continue 

the motor driving is occurring. 

 

c)  The one-touch tuning cannot be executed during the following test operation mode. 

Output signal (DO) forced output 
Motor-less operation 

 

d) If one-touch tuning is performed when the gain switching function is enabled, vibration and/or 

unusual noise may occur during the tuning. 

 

2)  Caution for amplifier command method 

a) Starting one-touch tuning while the servo motor is rotating displays "C006" at status in error 

code, and the one-touch tuning cannot be executed. 

 

b) Start one-touch tuning when all connected servo motors are at a stop. 

 

c)  One-touch tuning is not available during the test operation mode. The following test operation 

modes cannot be executed during one-touch tuning. 

 

Positioning operation 
JOG operation 
Program operation 
Machine analyzer operation 

 

d) After one-touch tuning is executed, control will not be performed by commands from the servo 

system controller. To return to the state in which control is performed from the servo system 
controller, reset the controller or cycle the power of the servo amplifier. 

 

e) During one-touch tuning, the permissible travel distance may be exceeded due to overshoot, 

set a value sufficient to prevent machine collision. 

 

f)  When Auto tuning mode 2, Manual mode, or 2 gain adjustment mode 2 is selected in [Pr. 

PA08 Auto tuning mode], the load to motor inertia ratio will not be estimated. An optimum 
acceleration/deceleration command will be generated by [Pr. PB06 Load to motor inertia 
ratio/load to motor mass ratio] at the start of one-touch tuning. When the load to motor inertia 
ratio is incorrect, the optimum acceleration/deceleration command may not be generated, 
causing the tuning to fail. 

 

g) When one-touch tuning is started by using USB communication, if the USB communication is 

interrupted during the tuning, the servo motor will stop, and the tuning will also stop. The 
parameter will return to the one at the start of the one-touch tuning. 

 

h) When one-touch tuning is started via the controller, if communication between the controller 

and the servo amplifier or personal computer is shut-off during the tuning, the servo motor will 
stop, and the tuning will also stop. The parameter will return to the one at the start of the one-
touch tuning. 

 

i)  When one-touch tuning is started during the speed control mode, the mode will be switched to 

the position control mode automatically. The tuning result may differ from the one obtained by 
executing tuning by using the speed command. 

 

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

CABASSE Stream Amp 100 Quick Start Manual preview
Stream Amp 100
Brand: CABASSE Pages: 2
Jensen XA2250 Installation And Operation Manual preview
XA2250
Brand: Jensen Pages: 12
T-audio TA-120 Operation Manual preview
TA-120
Brand: T-audio Pages: 13
Sonic Frontiers Sonic Frontiers Power 1 Operating Manual preview
Sonic Frontiers Power 1
Brand: Sonic Frontiers Pages: 17
ORANGE Crush PiX 20L Owner'S Manual preview
Crush PiX 20L
Brand: ORANGE Pages: 13
DUB Edition DUBa1450 Installation And Operation Manual preview
DUBa1450
Brand: DUB Edition Pages: 18
Optimus UP120M4 Manual preview
UP120M4
Brand: Optimus Pages: 19
Rockford Fosgate Punch P1000X4D Installation & Operation Manual preview
Punch P1000X4D
Brand: Rockford Fosgate Pages: 12
Vanguard SSDA200 Owner'S Manual preview
SSDA200
Brand: Vanguard Pages: 4
COMMERCIAL AUDIO 36374 User Manual preview
36374
Brand: COMMERCIAL AUDIO Pages: 17
Denon PMA-525R Operating Instructions Manual preview
PMA-525R
Brand: Denon Pages: 44
PBN EDFA-R Product User Manual preview
EDFA-R
Brand: PBN Pages: 32
SPITFIRE AUDIO APERTURE User Manual preview
APERTURE
Brand: SPITFIRE AUDIO Pages: 24
Soundstream Reference Series 1000S Installation Manual preview
Reference Series 1000S
Brand: Soundstream Pages: 12
NAD C 316 BEE Owner'S Manual preview
C 316 BEE
Brand: NAD Pages: 12
Tekbox TBMDA1 User Manual preview
TBMDA1
Brand: Tekbox Pages: 10
Ace Plus EX-G015 User Manual preview
EX-G015
Brand: Ace Plus Pages: 11
Soundigital POWER 35000.1D Installation Instructions Manual preview
POWER 35000.1D
Brand: Soundigital Pages: 14

Brands by name

Popular brands

Load more brands