manualshive.com logo in svg

Mitsubishi Electric MR-J4W2-0303B6, Instruction Manual

The Mitsubishi Electric MR-J4W2-0303B6 is a cutting-edge product designed to deliver precise and efficient performance. For users in need of guidance, an easy-to-understand Instruction Manual is available for free download at manualshive.com. Unlock the full potential of this exceptional product with our comprehensive manual.

Share
Download
background image

13. USING STO FUNCTION 

13 -  11 

 
13.4 Detailed description of interfaces 

This section provides the details of the I/O signal interfaces (refer to the I/O division in the table) given in 
section 13.2. Refer to this section and make connection with the external device. 
 
13.4.1 Sink I/O interface 

(1)  Digital input interface DI-1 

This is an input circuit whose photocoupler cathode side is the input terminal. Transmit signals from sink 
(open-collector) type transistor output, relay switch, etc. 

Approx. 3.0 k

Ω

STO1

STO2

Servo amplifier

Switch

Approx. 5 mA

For transistor

STOCOM

TR

24 V DC ± 10%
MR-J4W2-_B: 350 mA
MR-J4W3-_B: 450 mA

V

CES

≤

1.0 V

I

CEO

≤

 100 µA

 

(2)  Digital output interface DO-1 

This is a circuit in which the collector of the output transistor is the output terminal. When the output 
transistor is turned on, the current will flow to the collector terminal. 
A lamp, relay or photocoupler can be driven. Install a diode (D) for an inductive load, or install an inrush 
current suppressing resistor (R) for a lamp load. 
(Rated current: 40 mA or less, maximum current: 50 mA or less, inrush current: 100 mA or less) A 
maximum of 5.2 V voltage drop occurs in the servo amplifier. 

 

(a)  When outputting two STO states by using each TOFB 

TOFCOM

Servo amplifier

TOFB2

If polarity of diode is
reversed, servo amplifier
will malfunction.

Load

TOFB1

Load

(Note)

24 V DC ± 10%

MR-J4W2-_B: 350 mA

MR-J4W3-_B: 450 mA

 

Note. If the voltage drop (maximum of 2.6 V) interferes with the relay operation, apply high 

voltage (maximum of 26.4 V) from external source. 

 

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

VAC Renaissance Operation & Maintenance Information preview
Renaissance
Brand: VAC Pages: 10
Jensen XA2250 Installation And Operation Manual preview
XA2250
Brand: Jensen Pages: 12
XIEGU XPA125 Instruction Manual preview
XPA125
Brand: XIEGU Pages: 16
Takstar E500W User Manual preview
E500W
Brand: Takstar Pages: 24
Harman Kardon HK 675 Owner'S Manual preview
HK 675
Brand: Harman Kardon Pages: 8
Harman JBL Stage A6004 Manual preview
JBL Stage A6004
Brand: Harman Pages: 4
Dali PHANTOM CI AMP-2500 DSP Installation Manual & User Manual preview
PHANTOM CI AMP-2500 DSP
Brand: Dali Pages: 29
DigiTech AA-0477 Owner'S Manual preview
AA-0477
Brand: DigiTech Pages: 4
StetSom V 400.4 User Manual preview
V 400.4
Brand: StetSom Pages: 4
Imagine VTM6801+ Installation And Operation Manual preview
VTM6801+
Brand: Imagine Pages: 52
E&I 3100L Instruction Manual preview
3100L
Brand: E&I Pages: 12
Amate Audio TPD User Manual preview
TPD
Brand: Amate Audio Pages: 59
Unika V-8000 User Instructions preview
V-8000
Brand: Unika Pages: 16
Harman JBL DSP4086 Owner'S Manual preview
JBL DSP4086
Brand: Harman Pages: 10
Q-tron Audio PA34B4 User Manual preview
PA34B4
Brand: Q-tron Audio Pages: 10
Monacor PA-900S Instruction Manual preview
PA-900S
Brand: Monacor Pages: 18
Blitz Audio BZCAPT20 Installation Manual preview
BZCAPT20
Brand: Blitz Audio Pages: 2
Haskel AA-15 Operating And Maintenance Instructions Manual preview
AA-15
Brand: Haskel Pages: 26

Brands by name

Popular brands

Load more brands