manualshive.com logo in svg

Mitsubishi Electric MR-J4W2-0303B6, Instruction Manual

The Mitsubishi Electric MR-J4W2-0303B6 is a cutting-edge product designed to deliver precise and efficient performance. For users in need of guidance, an easy-to-understand Instruction Manual is available for free download at manualshive.com. Unlock the full potential of this exceptional product with our comprehensive manual.

Share
Download
background image

11. OPTIONS AND PERIPHERAL EQUIPMENT 

11 -  26 

 
(2)  Connection with servo amplifier 

To USB

connector

USB cable

MR-J3USBCBL3M

(Option)

Personal computer

Servo amplifier

CN5

(Note)

 

Note. CN5 is located under the display cover. 

 
11.4.3 Precautions for using USB communication function 

Note the following to prevent an electric shock and malfunction of the servo amplifier. 
 
(1)  Power connection of personal computers 

Connect your personal computer with the following procedures. 

 

(a)  When you use a personal computer with AC power supply 

1)  When using a personal computer with a three-core power plug or power plug with grounding wire, 

use a three-pin socket or ground the grounding wire. 

 

2)  When your personal computer has two-core plug and has no grounding wire, connect the 

personal computer to the servo amplifier with the following procedures. 

 

a) Disconnect the power plug of the personal computer from an AC power socket. 

 

b) Check that the power plug was disconnected and connect the device to the servo amplifier. 

 

c)  Connect the power plug of the personal computer to the AC power socket. 

 

(b)  When you use a personal computer with battery 

You can use as it is. 

 
(2)  Connection with other devices using servo amplifier communication function 

When the servo amplifier is charged with electricity due to connection with a personal computer and the 
charged servo amplifier is connected with other devices, the servo amplifier or the connected devices 
may malfunction. Connect the servo amplifier and other devices with the following procedures. 

 

(a)  Shut off the power of the device for connecting with the servo amplifier. 

 

(b)  Shut off the power of the servo amplifier which was connected with the personal computer and 

check the charge lamp is off. 

 

(c)  Connect the device with the servo amplifier. 

 

(d)  Turn on the power of the servo amplifier and the device. 

 

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

zapco C2K Owner'S Manual preview
C2K
Brand: zapco Pages: 71
Xtant 403A Owner'S Manual preview
403A
Brand: Xtant Pages: 13
JEFF ROWLAND 625 Operational Manual preview
625
Brand: JEFF ROWLAND Pages: 13
Van Medevoort CA350 Instruction Manual preview
CA350
Brand: Van Medevoort Pages: 8
Tascam PA-150 Specifications preview
PA-150
Brand: Tascam Pages: 2
Radio Frequency Systems 48710 User Manual preview
48710
Brand: Radio Frequency Systems Pages: 14
LA Audio DA82 User Manual preview
DA82
Brand: LA Audio Pages: 7
OSEE BDA6801N User Manual preview
BDA6801N
Brand: OSEE Pages: 12
Kompernass KH 5010 Operating Instructions Manual preview
KH 5010
Brand: Kompernass Pages: 49
PA Tech QSM-306V User Manual preview
QSM-306V
Brand: PA Tech Pages: 5
Dali PHANTOM CI AMP-2500 DSP Installation Manual & User Manual preview
PHANTOM CI AMP-2500 DSP
Brand: Dali Pages: 29
DigiTech AA-0477 Owner'S Manual preview
AA-0477
Brand: DigiTech Pages: 4
Induction Dynamics A2 AMP Owner'S Manual preview
A2 AMP
Brand: Induction Dynamics Pages: 4
Marshall Amplification G50RCD User Manual preview
G50RCD
Brand: Marshall Amplification Pages: 8
ALLNIC AUDIO HPA-3000GT Owner'S Manual preview
HPA-3000GT
Brand: ALLNIC AUDIO Pages: 6
Tokyo HL-130U Instruction Manual preview
HL-130U
Brand: Tokyo Pages: 11
PJB Bighead Owner'S Manual preview
Bighead
Brand: PJB Pages: 7
Rotel RKB-2100 Owner'S Manual preview
RKB-2100
Brand: Rotel Pages: 12

Brands by name

Popular brands

Load more brands