manualshive.com logo in svg

Mitsubishi Electric MR-J4W2-0303B6, Instruction Manual

The Mitsubishi Electric MR-J4W2-0303B6 is a cutting-edge product designed to deliver precise and efficient performance. For users in need of guidance, an easy-to-understand Instruction Manual is available for free download at manualshive.com. Unlock the full potential of this exceptional product with our comprehensive manual.

Share
Download
background image

17. APPLICATION OF FUNCTIONS 

17 -  30 

 

a) User command method 

It is recommended to input commands meeting the following conditions to the servo amplifier. 
If one-touch tuning is executed while commands which do not meet the conditions are inputted 
to the servo amplifier, the one-touch tuning error may occur. 

Servo motor

speed

Forward

rotation

0 r/min

Reverse

rotation

One cycle time

Dwell time

Deceleration

time constant

Travel distance

Acceleration

time constant

 

Fig. 17.1 Recommended command for one-touch tuning in the user command method 

 

Item Description 

Travel distance 

Set 100 pulses or more in encoder unit. Setting less than 100 pulses will cause the one-touch tuning error 
"C004". 

Servo motor speed  Set 150 r/min (mm/s) or higher. Setting less than 150 r/min (mm/s) may cause the one-touch tuning error "C005". 

Acceleration time 
constant 
Deceleration time 
constant 

Set the time to reach 2000 r/min (mm/s) to 5 s or less. 
Set an acceleration time constant/deceleration time constant so that the acceleration/deceleration torque is 10% 
or more of the rated torque. 
The estimation accuracy of the load to motor inertia ratio is more improved as the acceleration/deceleration 
torque is larger, and the one-touch tuning result will be closer to the optimum value. 

Dwell time 

Set 200 ms or more. Setting a smaller value may cause the one-touch tuning error "C004". 

One cycle time 

Set 30 s or less. Setting over 30 s will cause the one-touch tuning error "C004". 

 

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

JBL 6290 Manual preview
6290
Brand: JBL Pages: 30
A and T Labs K6 Assembly Manual preview
K6
Brand: A and T Labs Pages: 44
MUSIC HALL PH25.2 Instruction Manual preview
PH25.2
Brand: MUSIC HALL Pages: 8
Roksan Audio Kandy K2 User Manual preview
Kandy K2
Brand: Roksan Audio Pages: 11
Altec Lansing 9440A POWER AMPLIFIER Specifications preview
9440A POWER AMPLIFIER
Brand: Altec Lansing Pages: 4
Crown DCi 2 1250N Operation Manual preview
DCi 2 1250N
Brand: Crown Pages: 72
Thinuna TA-120D II Operation Manual preview
TA-120D II
Brand: Thinuna Pages: 12
Fenton AV150BT Instruction Manual preview
AV150BT
Brand: Fenton Pages: 7
Genz Benz SHUTTLE MAX 12.0 Owner'S Manual preview
SHUTTLE MAX 12.0
Brand: Genz Benz Pages: 9
Conrad-Johnson Premier Four Owner'S Manual preview
Premier Four
Brand: Conrad-Johnson Pages: 12
Crate KXB50 User Manual preview
KXB50
Brand: Crate Pages: 4
Lanzar MAX PRO MAXP 1200N User Manual preview
MAX PRO MAXP 1200N
Brand: Lanzar Pages: 9
ATEN KVMP CM1164 Quick Start Manual preview
KVMP CM1164
Brand: ATEN Pages: 2
Laney Ironheat IRT30-112 User Manual preview
Ironheat IRT30-112
Brand: Laney Pages: 16
Chord 173.442 User Manual preview
173.442
Brand: Chord Pages: 4
VINCENT SAV-C1 Instructions For Use Manual preview
SAV-C1
Brand: VINCENT Pages: 61
Kramer PA-225NET Preliminary User'S Manual preview
PA-225NET
Brand: Kramer Pages: 19
Soundigital LINHA EVOLUTION Owner'S Manual preview
LINHA EVOLUTION
Brand: Soundigital Pages: 7

Brands by name

Popular brands

Load more brands