Mitsubishi Electric MR-J4W2-0303B6 Instruction Manual Download Page 170 | Manualshive

Page: 170 / 588

background image

6. NORMAL GAIN ADJUSTMENT

6 - 17

6.2.3 Caution for one-touch tuning

(1) Caution common for user command method and amplifier command method

(a) The tuning is not available in the torque control mode.

(b) The one-touch tuning cannot be executed while an alarm or warning which does not continue the

motor driving is occurring.

(c) The one-touch tuning cannot be executed during the following test operation mode.

1) Output signal (DO) forced output

2) Motor-less operation

(d) If one-touch tuning is performed when the gain switching function is enabled, vibration and/or

unusual noise may occur during the tuning.

(2) Caution for amplifier command method

(a) Starting one-touch tuning while the servo motor is rotating displays "C006" at status in error code,

and the one-touch tuning cannot be executed.

(b) Start one-touch tuning when all connected servo motors are at a stop.

(c) One-touch tuning is not available during the test operation mode. The following test operation modes

cannot be executed during one-touch tuning.

1) Positioning operation

2) JOG operation

3) Program operation

4) Machine analyzer operation

(d) After one-touch tuning is executed, control will not be performed by commands from the servo

system controller. To return to the state in which control is performed from the servo system
controller, reset the controller or cycle the power of the servo amplifier.

(e) During one-touch tuning, the permissible travel distance may be exceeded due to overshoot, set a

value sufficient to prevent machine collision.

(f) When Auto tuning mode 2, Manual mode, or 2 gain adjustment mode 2 is selected in [Pr. PA08 Auto

tuning mode], the load to motor inertia ratio will not be estimated. An optimum
acceleration/deceleration command will be generated by [Pr. PB06 Load to motor inertia ratio/load to
motor mass ratio] at the start of one-touch tuning. When the load to motor inertia ratio is incorrect,
the optimum acceleration/deceleration command may not be generated, causing the tuning to fail.

(g) When one-touch tuning is started by using USB communication, if the USB communication is

interrupted during the tuning, the servo motor will stop, and the tuning will also stop. The parameter
will return to the one at the start of the one-touch tuning.

(h) When one-touch tuning is started via the controller, if communication between the controller and the

servo amplifier or personal computer is shut-off during the tuning, the servo motor will stop, and the
tuning will also stop. The parameter will return to the one at the start of the one-touch tuning.

(i) When one-touch tuning is started during the speed control mode, the mode will be switched to the

position control mode automatically. The tuning result may differ from the one obtained by executing
tuning by using the speed command.

«
...
168
169
170
171
172
...
»

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

Brand: Randall Pages: 9

Brand: Eclipse Pages: 22

Brand: Ecleree Pages: 38

Brand: Peavey Pages: 14

Brand: AR Pages: 56

Brand: Acesonic Pages: 22

Brand: FMS Pages: 24

Brand: Xicom Pages: 36

ZeroUno DAC-HPA

Brand: Canever Pages: 8

Brand: Teac Pages: 96

Brand: M-system Pages: 4

Brand: Parker Pages: 8

Brand: Power Acoustik Pages: 11

Brand: Aura Pages: 12

Brand: Sonelco Pages: 2

VINGTOR STENTOFON EA1400

Brand: Zenitel Pages: 17

Brand: Carson Pages: 12

Brand: WORLD DESIGNS Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands