manualshive.com logo in svg

Mitsubishi Electric MR-J4W2-0303B6, Instruction Manual

The Mitsubishi Electric MR-J4W2-0303B6 is a cutting-edge product designed to deliver precise and efficient performance. For users in need of guidance, an easy-to-understand Instruction Manual is available for free download at manualshive.com. Unlock the full potential of this exceptional product with our comprehensive manual.

Share
Download
background image

6. NORMAL GAIN ADJUSTMENT 

6 -  2 

 
(2)  Adjustment sequence and mode usage 

2 gain adjustment mode 1

(interpolation mode)

Interpolation

made for 2 or more

axes?

The load fluctuation

is large during driving?

Start

End

Yes

No

Yes

No

Yes

No

No

Yes

One-touch tuning

Yes

Yes

Yes

Error handling

is possible?

Handle the error

Adjustment OK?

Finished normally?

2 gain adjustment mode 2

Manual mode

Auto tuning mode 1

Yes

Adjustment OK?

Auto tuning mode 2

No

No

No

Adjustment OK?

Adjustment OK?

No

 

6.1.2 Adjustment using MR Configurator2 

This section explains the functions and adjustment using the servo amplifier with MR Configurator2. 

 

Function Description 

Adjustment 

Machine analyzer 

With the machine and servo motor coupled, 
the characteristic of the mechanical system 
can be measured by giving a random 
vibration command from a personal 
computer to the servo and measuring the 
machine response. 

You can grasp the machine resonance 
frequency and determine the notch 
frequency of the machine resonance 
suppression filter. 

 

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

Gallien-Krueger 250ML Service Manual preview
250ML
Brand: Gallien-Krueger Pages: 19
DAD DP8000 User Manual preview
DP8000
Brand: DAD Pages: 24
W Audio SB-300 Operation Manual preview
SB-300
Brand: W Audio Pages: 20
Xicom XTS-200C Operation And Installation Manual preview
XTS-200C
Brand: Xicom Pages: 168
Total Mobile Audio T2-320.4 Owner'S Manual preview
T2-320.4
Brand: Total Mobile Audio Pages: 11
Lynx D VD 5002 Reference Manual preview
D VD 5002
Brand: Lynx Pages: 22
Qtx QS12A User Manual preview
QS12A
Brand: Qtx Pages: 3
Klipsch ProMedia DD-5.1 User Manual preview
ProMedia DD-5.1
Brand: Klipsch Pages: 34
IRT Electronics DVA-3006 Instruction Manual preview
DVA-3006
Brand: IRT Electronics Pages: 10
M-system 20VS5-500 Instruction Manual preview
20VS5-500
Brand: M-system Pages: 4
MAG THEATRON TDC Series User Manual preview
TDC Series
Brand: MAG THEATRON Pages: 28
Boss DNX3500 User Manual preview
DNX3500
Brand: Boss Pages: 16
Denon PMA-2000AE Service Manual preview
PMA-2000AE
Brand: Denon Pages: 34
GME GA9800 Instruction Manual preview
GA9800
Brand: GME Pages: 12
Fender 2300100000 Quick Start Manual preview
2300100000
Brand: Fender Pages: 12
JL Audio RD500/1 Owner'S Manual preview
RD500/1
Brand: JL Audio Pages: 20
NuWaves NUPOWER XTENDER VU4GX01 User Manual preview
NUPOWER XTENDER VU4GX01
Brand: NuWaves Pages: 11
JET CITY AMPLIFICATION JCA22H Owner'S Manual preview
JCA22H
Brand: JET CITY AMPLIFICATION Pages: 18

Brands by name

Popular brands

Load more brands