manualshive.com logo in svg

Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010, Configuration Manual

The Juniper JUNOSE 11.1.X Link Layer Configuration Manual, released on 4-7-2010, is a comprehensive guide for configuring link layer settings. Users can easily download this manual for free from our website, ensuring they have the necessary resources to effectively set up their network infrastructure.

Share
Download
background image

host1#

show ppp interface fastEthernet 12/0.1.1 full

PPP interface FastEthernet 12/0.1.1 is lowerDown

Interface administrative status is open
Configured network protocol is IPV6CP
IPCP protocol configuration
   configured                     false
   administrative-status          open
   ip-address                     0.0.0.0
   dns-precedence                 local
   wins-precedence                local
   ipcp-netmask-option            disabled
   ipcp-lockout-option            enabled
   max-negotiations               10
IPCP protocol status
   operational-status             not present

IPV6CP protocol configuration
   configured                     true
   administrative-status          open
   ipv6-interfaceId               90:1a00:140:4b39
IPV6CP protocol status
   operational-status             down 
   terminate-reason               link down

OSINLCP protocol configuration
   configured                     false
   administrative-status          open
OSINLCP protocol status
   operational-status             not present

Interface statistics              in                   out
   packets                        0                    0
   octets                         1163                 706
   errors                         0                    0
   discards                       153482               0 

LCP protocol configuration
   max-receive-unit               use lower layer
   authentication                 none
   magic-number                   enabled
   magic-number-mismatch          reject 
   keepalive-timer                30 seconds
   restart-timer                  3 seconds
   max-terminate                  2
   max-configure                  10
   max-failure                    5
   passive-mode                   disabled
LCP protocol status
   link-status                    initial
LCP protocol statistics
   in-keepalive-requests          11
   out-keepalive-requests         11
   in-keepalive-replies           11
   out-keepalive-replies          11
   keepalive-failures             0
Authentication configuration
   authenticate-retry             0
   authentication-router          ''

Monitoring PPP Interfaces

■

297

Chapter 8: Configuring Point-to-Point Protocol

Summary of Contents for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Waves Linear-Phase MultiBand Software Audio Processor User Manual preview
Linear-Phase MultiBand Software Audio Processor
Brand: Waves Pages: 27
VegaStream Vega Gateway Engineer'S Manual preview
Vega Gateway
Brand: VegaStream Pages: 33
Novell EVOLUTION 2.6 Manual preview
EVOLUTION 2.6
Brand: Novell Pages: 126
Altigen AltiContact Manager Version 5.0 Administration Manual preview
AltiContact Manager Version 5.0
Brand: Altigen Pages: 542
Tech Source RAPTOR 1100T - X11R6.1 FOR AIX Installation Manual preview
RAPTOR 1100T - X11R6.1 FOR AIX
Brand: Tech Source Pages: 40
Fiery Fiery EX2101 Job Management Manual preview
Fiery EX2101
Brand: Fiery Pages: 214
GRASS VALLEY AURORA INGEST 7 Datasheet preview
AURORA INGEST 7
Brand: GRASS VALLEY Pages: 4
GRASS VALLEY Aurora Browse Upgrade Instructions preview
Aurora Browse
Brand: GRASS VALLEY Pages: 42
MACROMEDIA DIRECTOR MX 2004-GETTING STARTED WITH... Getting Started preview
DIRECTOR MX 2004-GETTING STARTED WITH...
Brand: MACROMEDIA Pages: 68
Native Instruments Studio Drummer User Manual preview
Studio Drummer
Brand: Native Instruments Pages: 41
IBM RELEASE 7.3 Management Manual preview
RELEASE 7.3
Brand: IBM Pages: 388
FARONICS DEEP FREEZE SERVER STANDARD Manual preview
DEEP FREEZE SERVER STANDARD
Brand: FARONICS Pages: 24
Quantum GoVault 40GB Quick Start Manual preview
GoVault 40GB
Brand: Quantum Pages: 16
FARONICS INSIGHT - TEACHER Quick Start Manual preview
INSIGHT - TEACHER
Brand: FARONICS Pages: 9
Access VIRUS|POWERCORE User'S Reference Manual preview
VIRUS|POWERCORE
Brand: Access Pages: 124
Campbell RTDM Instruction Manual preview
RTDM
Brand: Campbell Pages: 22
DAVIS Weather Talker User Manual preview
Weather Talker
Brand: DAVIS Pages: 49
Canon SELPHY CP760 Software Manual preview
SELPHY CP760
Brand: Canon Pages: 50

Brands by name

Popular brands

Load more brands