manualshive.com logo in svg

Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010, Configuration Manual

The Juniper JUNOSE 11.1.X Link Layer Configuration Manual, released on 4-7-2010, is a comprehensive guide for configuring link layer settings. Users can easily download this manual for free from our website, ensuring they have the necessary resources to effectively set up their network infrastructure.

Share
Download
background image

8.

Configure the interface to detect and accept dynamic PPPoE subinterfaces.

host1(config-subif)#

pppoe auto-configure

S-VLAN Oversubscription

When you configure S-VLAN subinterfaces over Ethernet interfaces to support dynamic
PPPoE subinterfaces, you can take advantage of S-VLAN oversubscription.

The maximum number of S-VLANs that you can create per I/O module or IOA with
PPPoE major interfaces stacked over them is greater than the maximum number of
dynamic PPPoE subinterfaces. The maximum number of PPP interfaces supported
per line module is directly proportional to the maximum number of PPPoE
subinterfaces.

As a result, you can oversubscribe S-VLANs by configuring up to the maximum
number of S-VLANs supported on the I/O module or IOA, knowing that no more than
the maximum number of supported PPP sessions can be connected to the router at
any one time.

For information about the module combinations that support S-VLAN oversubscription,
see “S-VLAN Oversubscription” on page 188 in “Configuring VLAN and S-VLAN
Subinterfaces” on page 169.

For specific information about the maximum number of S-VLANs supported per I/O
module or IOA and the maximum number of PPP interfaces and PPPoE subinterfaces
supported per line module, see 

JUNOSe Release Notes

, 

Appendix A

, 

System Maximums

.

NOTE:

S-VLAN oversubscription is not currently supported for S-VLANs configured

over bridged Ethernet interfaces.

The E120 and E320 routers can support up to two IOAs per line module. This
maximum number of S-VLANs per line module does not change whether one or two
IOAs are installed. For more information about configuration options for the ES2-S1
GE-4 IOA, see chapter Configuring Ethernet Interfaces in 

JUNOSe Physical Layer

Configuration Guide

.

atm pvc

Use to configure a PVC on an ATM interface. Specify one of the following
encapsulation types:

■

■

aal5autoconfig

—Enables autodetection of the 1483 encapsulation (LLC/SNAP

or VC multiplexed).

■

aal5snap

—Specifies a logical link control (LLC) encapsulated circuit; the

LLC/Subnetwork Access Protocol (LLC/SNAP) header precedes the protocol
datagram.

544

■

Configuring PPPoE Dynamic Interfaces over PPPoE Static Interfaces

JUNOSe 11.1.x Link Layer Configuration Guide

Summary of Contents for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Snom Configuring snom phones for Mass Deployment Frequently Asked Questions Manual preview
Configuring snom phones for Mass Deployment
Brand: Snom Pages: 22
Genesys Hosted Provider Edition (HPE) 8.1 Product Availability Announcement preview
Hosted Provider Edition (HPE) 8.1
Brand: Genesys Pages: 5
MACROMEDIA CONTRIBUTE 3 - USING AND ADMINISTERING... Use Manual preview
CONTRIBUTE 3 - USING AND ADMINISTERING...
Brand: MACROMEDIA Pages: 256
American DJ myDMX 2.0 User Instructions preview
myDMX 2.0
Brand: American DJ Pages: 21
Mitsubishi WiFi-Doc Client for iOS User Manual preview
WiFi-Doc Client for iOS
Brand: Mitsubishi Pages: 10
SanDisk Membrain Software User Manual preview
Membrain Software
Brand: SanDisk Pages: 14
IBM BJ0NJML - Service And Asset Management Integration Manual preview
BJ0NJML - Service And Asset Management
Brand: IBM Pages: 330
Dragon Systems DRAGON NATURALLYSPEAKING PROFESSIONAL 5 Manual preview
DRAGON NATURALLYSPEAKING PROFESSIONAL 5
Brand: Dragon Systems Pages: 222
Casio FA-B30 User Manual preview
FA-B30
Brand: Casio Pages: 68
Seagate ST905003BPA1E1-RK - Maxtor BlackArmor 500 GB External Hard Drive Specifications preview
ST905003BPA1E1-RK - Maxtor BlackArmor 500 GB External Hard Drive
Brand: Seagate Pages: 2
Promise Technology PAM User Manual preview
PAM
Brand: Promise Technology Pages: 84
Promise Technology dc5750 - Microtower PC User Manual preview
dc5750 - Microtower PC
Brand: Promise Technology Pages: 114
SimpleTech SimpleDrive SP-U25/120 Quick Start Manual preview
SimpleDrive SP-U25/120
Brand: SimpleTech Pages: 8
Zing Magic Checkers User Manual preview
Checkers
Brand: Zing Magic Pages: 10
Lowrance MapCreate 6 Install And Operation Instructions preview
MapCreate 6
Brand: Lowrance Pages: 76
THOMSON LCP 400 User Manual preview
LCP 400
Brand: THOMSON Pages: 22
Janome AcuFil Tips And Tricks Manual preview
AcuFil
Brand: Janome Pages: 6
Lenovo ThinkPad X301 Hardware Maintenance Manual preview
ThinkPad X301
Brand: Lenovo Pages: 154

Brands by name

Popular brands

Load more brands