Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010 Configuration Manual Download Page 242 | Manualshive

Page: 242 / 774

background image

host1(config-if)#

speed 100

host1(config-if)#

duplex full

host1(config-if)#

lacp active

host1(config-if)#

interface fastEthernet 5/1

host1(config-if)#

speed 100

host1(config-if)#

duplex full

host1(config-if)#

lacp active

The following commands create a virtual router, add the Ethernet physical interfaces
to a LAG bundle named kanata, assign an IP address, and configure MPLS.

host1(config)#

virtual router kanata

host1:kanata(config)#

interface lag kanata

host1:kanata(config-if)#

member-interface fastEthernet 0/0

host1:kanata(config-if)#

member-interface fastEthernet 0/5

host1:kanata(config-if)#

ip address 1.1.1.1 255.255.255.0

host1(config-if)#

mpls

Example: Configuring MPLS over a VLAN for a LAG Bundle

The following example displays configuration of LACP for two Fast Ethernet interfaces
in slot 5. The interfaces are enabled for active LACP. The speed and duplex
characteristics are the same for both interfaces.

host1(config)#

interface fastEthernet 5/0

host1(config-if)#

speed 100

host1(config-if)#

duplex full

host1(config-if)#

lacp active

host1(config-if)#

interface fastEthernet 5/1

host1(config-if)#

speed 100

host1(config-if)#

duplex full

host1(config-if)#

lacp active

The following commands add the Ethernet physical interfaces to a LAG bundle named
kanata.

host1(config)#

virtual router kanata

host1:kanata(config)#

interface lag kanata

host1:kanata(config-if)#

member-interface fastEthernet 5/0

host1:kanata(config-if)#

member-interface fastEthernet 5/1

The following commands configure a VLAN subinterface for the LAG bundle named
kanata. In the LAG interface identification command (

interface lag kanata.1

), the

number 1 represents the subinterface number for the VLAN subinterface.

host1:kanata(config-if)#

encapsulation vlan

host1:kanata(config)#

interface lag kanata.1

host1:kanata(config-if)#

vlan id 100

The following command creates an MPLS interface.

host1:kanata(config)#

mpls

210

■

Example: Configuring MPLS over a VLAN for a LAG Bundle

JUNOSe 11.1.x Link Layer Configuration Guide

«
...
240
241
242
243
244
...
»

Summary of Contents for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

SimNow Simulator 4.4.5

Brand: AMD Pages: 269

Brand: Juniper Pages: 748

COLDFUSION MX 61-GETTING STARTED BUILDING COLDFUSION...

Brand: MACROMEDIA Pages: 134

FLASH 8-USING FLASH VIDEO ENCODER

Brand: MACROMEDIA Pages: 30

ST905003BPA1E1-RK - Maxtor BlackArmor 500 GB External Hard Drive

Brand: Seagate Pages: 2

Brand: LinPlug Pages: 46

Wireless PCI Adapter Driver

Brand: 2Wire Pages: 4

Brand: A&D Pages: 36

Brand: Sonifex Pages: 68

Brand: da Vinci Technologies Pages: 249

Brand: Focusrite Pages: 9

15606-011408-9008 - MAPGUIDE R6.3 NAMED-100U PK

Brand: Autodesk Pages: 204

CORE - MIGRATION GUIDE 11-2009

Brand: FARONICS Pages: 32

Brand: DRAKE Pages: 2

Brand: Canon Pages: 69

Netcool/OMNIbus Probe for Nortel CNM

Brand: IBM Pages: 34

Brand: JVC Pages: 9

GY-DV300U - 1/3" 3-ccd Dv Camcorder

Brand: JVC Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands