manualshive.com logo in svg

Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010, Configuration Manual

The Juniper JUNOSE 11.1.X Link Layer Configuration Manual, released on 4-7-2010, is a comprehensive guide for configuring link layer settings. Users can easily download this manual for free from our website, ensuring they have the necessary resources to effectively set up their network infrastructure.

Share
Download
background image

Authentication ......................................................................................267
Rate Limiting for PPP Control Packets ..................................................267
Extensible Authentication Protocol .......................................................267

EAP Types ......................................................................................268
EAP Packet Retransmission ............................................................268
EAP Behavior in an L2TP Environment ..........................................269
Limitations .....................................................................................270
Performance ..................................................................................270

Remote Peer Scenarios During Negotiation of PPP Options ..................271
IPCP Lockout and Local IP Address Pool Restoration ............................272

Platform Considerations ..............................................................................273

Module Requirements ...........................................................................273
Interface Specifiers ...............................................................................273

References ..................................................................................................274
Before You Configure PPP ...........................................................................275
Configuration Tasks .....................................................................................275
Optional Configuration Tasks ......................................................................278

Configuring PPP Authentication ............................................................283

PPP Accounting Statistics ............................................................................285
Monitoring PPP Interfaces ...........................................................................286
Troubleshooting ..........................................................................................300

Chapter 9

Configuring Multilink PPP

303

Overview .....................................................................................................303

Application ...........................................................................................304
MLPPP LCP Extensions .........................................................................304
MLPPP Link Selection ...........................................................................305

Platform Considerations ..............................................................................306

Module Requirements ...........................................................................307
Interface Specifiers ...............................................................................307

References ..................................................................................................307
Supported MLPPP Features .........................................................................308
Unsupported MLPPP Features .....................................................................312
Before You Configure Static MLPPP .............................................................312
Configuring Static MLPPP ............................................................................312

Configuration Example .........................................................................314
Contextual Command Differences ........................................................314
Configuring Authentication ...................................................................315
Configuring Other PPP Attributes ..........................................................317

Configuring Dynamic MLPPP ......................................................................323
Configuring MLPPP Fragmentation and Reassembly ...................................324

Overview ..............................................................................................324

Application .....................................................................................325
Supported Configurations ...............................................................325
Module Requirements ....................................................................325
Link Configuration Parameters .......................................................325
Bundle Validation and Configuration Guidelines .............................326
Bundle Validation Failure ................................................................327

Table of Contents

■

xv

Table of Contents

Summary of Contents for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

UMAX Technologies PowerColor Quick Start Manual preview
PowerColor
Brand: UMAX Technologies Pages: 10
Xerox WORKCENTRE C2424 Manual preview
WORKCENTRE C2424
Brand: Xerox Pages: 12
Xerox WorkCentre M118 Getting Started Manual preview
WorkCentre M118
Brand: Xerox Pages: 25
Xerox 850DP - Phaser Color Solid Ink Printer Installation Instructions preview
850DP - Phaser Color Solid Ink Printer
Brand: Xerox Pages: 2
FARONICS ANTI-EXECUTABLE ENTERPRISE Manual preview
ANTI-EXECUTABLE ENTERPRISE
Brand: FARONICS Pages: 68
Lenovo Active Protection System Manual preview
Active Protection System
Brand: Lenovo Pages: 10
Lenovo Aptiva Hardware Maintenance Manual preview
Aptiva
Brand: Lenovo Pages: 464
Lenovo ACTIVATION Error Code List preview
ACTIVATION
Brand: Lenovo Pages: 3
COMPRO Y-C User Manual preview
Y-C
Brand: COMPRO Pages: 8
Polycom CMA V4.0 User Manual preview
CMA V4.0
Brand: Polycom Pages: 23
M-Audio Torq 1.5 User Manual preview
Torq 1.5
Brand: M-Audio Pages: 99
Sonifex Mentor Time-Server User Handbook preview
Mentor Time-Server
Brand: Sonifex Pages: 4
Pfaff CREATIVE 4D EXPRESS MONOGRAM WIZARD Brochure preview
CREATIVE 4D EXPRESS MONOGRAM WIZARD
Brand: Pfaff Pages: 2
GameShark GAME CUBE Instruction Manual preview
GAME CUBE
Brand: GameShark Pages: 16
F-SECURE MOBILE SECURITY 3.1 FOR S60 User Manual preview
MOBILE SECURITY 3.1 FOR S60
Brand: F-SECURE Pages: 31
Labelmaster Masterform 3.0 User Manual preview
Masterform 3.0
Brand: Labelmaster Pages: 81
Planet DrView User Manual preview
DrView
Brand: Planet Pages: 55
Focusrite Plug-in Suite User Manual preview
Plug-in Suite
Brand: Focusrite Pages: 9

Brands by name

Popular brands

Load more brands