Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010 Configuration Manual Download Page 210

Page: 210 / 774

Figure 17 on page 178 illustrates the configuration steps for two VLAN subinterfaces.
In this example:

■

VLAN subinterface 4/1.1 has an IP interface, a PPPoE interface, and multiple
PPPoE subinterface stacks.

■

VLAN subinterface 4/1.2 has only an IP interface.

NOTE:

Before you can remove a VLAN subinterface, you must remove the upper-layer

interface stack.

Figure 17: Example of PPPoE over VLAN with IP over VLAN Stacking Configuration Procedure

encapsulation ppp

■

Use to configure PPP as the encapsulation method for the interface.

■

Example

host1(config-if)#

encapsulation ppp

■

Use the no version to disable PPP on the interface.

■

See encapsulation ppp.

178

■

Creating a VLAN Subinterface

JUNOSe 11.1.x Link Layer Configuration Guide

Summary of Contents for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Reviews:

Related manuals for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Brands by name

Popular brands

Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010, Configuration Manual

Search results

Summary of Contents for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Reviews:

Related manuals for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Brands by name

Popular brands