Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010 Configuration Manual Download Page 164

Page: 164 / 774

In discards: 0 Out discards: 0
In unknown protos: 0

■

See show frame-relay subinterface.

show frame-relay summary

■

Use to scan all defined Frame Relay interfaces and circuits; reports aggregate
status as one of the following:

■

Up—Traffic can flow on the interface

■

Down—Traffic cannot flow because of a problem in the network

■

Unavailable—Traffic cannot flow because hardware is unavailable

■

Example

host1#

show frame-relay summary

28 interface(s) defined, 28 up, 0 down
840 sub-interface(s) defined, 840 up, 0 down
840 circuit(s) defined, 840 up, 0 down

■

See show frame-relay summary.

132

■

Monitoring Frame Relay

JUNOSe 11.1.x Link Layer Configuration Guide

Summary of Contents for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Reviews:

Related manuals for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Brands by name

Popular brands

Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010, Configuration Manual

Search results

Summary of Contents for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Reviews:

Related manuals for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Brands by name

Popular brands