Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010 Configuration Manual Download Page 569

Page: 569 / 774

Figure 49: Dynamic PPPoE over Static PPPoE with VLAN Interface Columns

To configure a VLAN subinterface to support a dynamic PPPoE subinterface:

Specify a Fast Ethernet, Gigabit Ethernet, or 10-Gigabit Ethernet interface.

host1(config)#

interface fastEthernet 4/1

Specify VLAN as the encapsulation method.

host1(config-if)#

encapsulation vlan

This command adds the VLAN major interface.

Create a VLAN subinterface by adding a subinterface number to the interface
identifier.

host1(config-if)#

interface fastEthernet 4/1.1

Assign a VLAN ID for the subinterface.

host1(config-if)#

vlan id 400

Set the encapsulation type to PPPoE.

host1(config-subif)#

encapsulation pppoe

Assign a profile.

host1(config-subif)#

pppoe profile pppoeProfile2

Configure the interface to detect and accept dynamic PPPoE subinterfaces.

host1(config-subif)#

pppoe auto-configure

Configuring PPPoE Dynamic Interfaces over PPPoE Static Interfaces

■

537

Chapter 17: Configuring Dynamic Interfaces

Summary of Contents for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Reviews:

Related manuals for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Brands by name

Popular brands

Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010, Configuration Manual

Search results

Summary of Contents for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Reviews:

Related manuals for JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Brands by name

Popular brands