manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 97 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 97

Instructions for Use Fabius MRI SW 3.n

97

Operation

Volume Control Ventilation

Ventilator Compliance Compensation

Ventilator compliance compensation is continu-
ously applied during Volume Control so that the 
tidal volume delivered to the patient corresponds to 
the V

T

 setting. Ventilator compliance is determined 

during the leak and compliance test performed from 
the Standby mode (see “Leak/Compliance Test” on 
page 136). To have compliance compensation work 
accurately, it is important that the patient hoses 
used during the leak/compliance test match the 
type of hoses used during the procedure.

Starting Volume Control Ventilation

The following examples and illustrations describe 
starting Volume Control ventilation from the present 
ventilation mode “Pressure Control”:

1

Press the »

Volume Control

« key. The LED 

associated with this key starts blinking. It 
remains blinking until the selected mode of 
operation is confirmed.

2

The Waveform window is replaced by the venti-
lator settings window and a message that pro-
vides instructions to confirm the mode change.

NOTE

When the ventilator settings for Volume Control 
cause the ventilator to operate at its limits of per-
formance, it is not possible for the Fabius MRI to 
apply compliance compensation. If the ventilator's 
performance limit is reached, it is not possible to 
increment the V

T

 setting via the Volume Control 

Settings window.

563

2

1

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments