Dräger Fabius Instructions For Use Manual Download Page 203

Page: 203 / 232

Instructions for Use Fabius MRI SW 3.n

203

Technical Data

Recommended separation distances

Information regarding separation distances
(IEC 60601-1-2: 2001, tables 205 and 206)

Recommended separation distances between portable and mobile RF telecommunication

devices and the Fabius MRI

max.

EIRP

(W)

3 V/m

distance

(m)

1) 3 V/m distance to transmitters with frequencies from 150 kHz to 2.5 GHz, otherwise 1 V/m distance.

1 V/m

distance

(m)

Note

0.001

0.06

0.17

0.003

0.10

0.30

0.010

0.18

0.55

0.030

0.32

0.95

e.g. WLAN 5250 / 5775 (Europe)

0.100

0.58

1.73

e.g. WLAN 2440 (Europe), Bluetooth

0.200

0.82

2.46

e.g. WLAN 5250 (not in Europe)

0.250

0.91

2.75

e.g. DECT devices

1.000

1.83

5.48

e.g. GSM 1800- / GSM 1900- / UMTS- mobiles,

WLAN 5600 (not in Europe)

2.000

2.60

7.78

e.g. GSM 900 mobiles

3.000

3.16

9.49

Summary of Contents for Fabius









































































































































































































































Search results

Summary of Contents for Fabius

Reviews:

Dräger Fabius, Instructions For Use Manual, Page: 203 / 232

Search results

Summary of Contents for Fabius

Reviews: