manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 174 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 174

174

Instructions for Use Fabius MRI SW 3.n

Cleaning

Removing anesthetic gas scavenging 
system (AGSS)

z

Remove the anesthetic gas receiving system 
(AGS) including scavenging hose and exhaust 
hose from the medical device.

Removing the Suction System

z

Remove suction bottle assembly, including bot-
tle and regulator.

Reprocessing Breathing system

All parts of the respiratory system, ventilator 
diaphragm, Y-piece, respiratory hoses, respira-
tory bag, parts of the absorber, parts of the sec-
retion suction unit and parts of the anesthetic 
gas scavenging system.

z

Thermally disinfect in the cleaning/disinfection 
machine at 200 °F (93 °C) /10 minutes.
Only use neutral or mild alcalic cleaning agents 
(e.g. Neodisher Medizym, Neodisher FA) and 
completely demineralized water!
When using thermal disinfection, the addition of 
disinfectant chemicals is not necessary; risk of 
corrosion!

WARNING
Risk of infection
Always wear protective gloves when emptying 
the suction bottle.
Observe the hospital hygiene regulations.

NOTE

Reprocessing/disinfection instructions for the 
reusable suction bottle and the suction regulator, 
refer to their respective Instructions for Use.

WARNING
After washing, a hot steam sterilization is 
required to completely dry the breathing sys-
tem.
Insufficient drying of the control areas found 
in the valve plate can lead to impairment of 
device function or to failure of the medical 
device.

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments