manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 23 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 23

System Overview

Instructions for Use Fabius MRI SW 3.n

23

Note that the selector lever is shown in the center 
position. This ensures that both vaporizers are in 
the locked position. Also, this is the recommended 
position for the selector lever when moving the 
Fabius MRI.

Dräger Auto Exclusion 2-Vaporizer Mount 
(Optional)

This system has an automatic interlock system that 
ensures only one vaporizer can be used at a time. 
When one of the two vaporizers is selected for use 
(opened), the interlock mechanism within that 
vaporizer’s mounting system is activated automati-
cally, preventing the other vaporizer from being 
used.

NOTE

Only Dräger vaporizers labeled as 
“AUTO EXCLUSION” vaporizers are compatible 
with the Dräger Auto Exclusion 2-Vaporizer Mount.

07

5

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments