manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 175 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 175

Instructions for Use Fabius MRI SW 3.n

175

Cleaning

O

2

 Sensor

Spirolog Infinity ID and SpiroLife flow sensors

Reprocess the flow sensor in accordance with the 
corresponding Instructions for Use.

Sterilization

Strictly follow the correct Instructions for Use.

Steam sterilization at 273 °F (134 °C)

Strictly follow the correct Instructions for Use.

All components with the suitable reprocessing 
options are listed in the maintenance list for 
Fabius MRI components page 176. Follow the 
hygiene regulations of the hospital!

CAUTION

Risk of equipment damage
The O

2

 sensor must not be sterilized or disin-

fected!

CAUTION

The flow sensor must not be reprocessed in a 
washer-disinfector. Do not clean with compressed 
air, water jet, brush, etc. Otherwise, the thin wires 
in the flow sensor may be destroyed. The Spirolog 
and Infinity ID flow sensor must not be sterilized in 
hot steam. The flow sensor is not resistant to high 
temperatures and will be destroyed.

CAUTION

Only use clean disinfectant solutions to disinfect 
the flow sensor. Contaminants, e.g., lint, may lead 
to the destruction of the flow sensor.

WARNING
Risk of fire hazard
Allow the flow sensor to dry in air for at least 
30 minutes after the use of disinfectants con-
taining flammable substances. These sub-
stances give off vapors that could ignite 
during calibration.

CAUTION

The flow sensor can only be reused as long as 
automatic calibration is possible.

CAUTION

Risk of damage to the medical device
The Spirolog and Infinity ID flow sensors must not 
be sterilized.

CAUTION

Risk of damage to the medical device
SpiroLife flow sensors are not suitable for plasma 
or radiation sterilization.

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments