Dräger Fabius Instructions For Use Manual Download Page 156

Page: 156 / 232

Configuration

156

Instructions for Use Fabius MRI SW 3.n

Access Alarm Log
1

Press the »

Access Alarm Log

« key in the

Setup window. The Setup window is replaced
by the alarm log, which lists all alarms with their
dates and times.

To scroll through the alarm log, turn the rotary
knob.

To delete all alarms from the log, select and
confirm the »

Clear Alarm Log

« label.

To exit the alarm log and return to the Setup
window, select and confirm the return arrow.

Access Alarm Volume
2

Press the »

Access Alarm Volume

« key in the

Setup window.

The Setup window is replaced by the Alarm Vol-
ume Setting window

Select and confirm a new alarm volume value in
the range of 1 (minimum) to 10 (maximum).

The value is saved and the Alarm Volume Setting
window is replaced by the Setup window.

556

562

Summary of Contents for Fabius









































































































































































































































Search results

Summary of Contents for Fabius

Reviews:

Dräger Fabius, Instructions For Use Manual, Page: 156 / 232

Search results

Summary of Contents for Fabius

Reviews: