manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 153 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 153

Instructions for Use Fabius MRI SW 3.n

153

Configuration

Volume Alarms On/Off
1

Press the »

Volume Alarms On

« soft key in the 

Setup window. The key label changes from 
»

Volume Alarms On

«

 

to »

Volume Alarms 

Off

«, and the volume alarms are disabled.

Auto Set
2

Press the »

Auto Set

« soft key in the Setup win-

dow. The breathing pressure threshold is set to 
4 cmH

2

O (hPa) below the current plateau pres-

sure data value.

NOTE

The »

Volume Alarms On/Off

« soft key label does 

not appear in ManSpont mode because it is select-
able on the ManSpont screen.

NOTE

The threshold setting may not be less than 
5 cmH

2

O (5 hPa) or greater than 30 cmH

2

O 

(30 hPa).

NOTE

In the absence of a current plateau pressure data 
value, pressing the soft key will have no effect.

NOTE

In SIMV/PS mode, the breathing pressure thresh-
old will be set relative to the mandatory ventilation 
stroke.

503

1

2

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments