Dräger Fabius Instructions For Use Manual Download Page 166

Page: 166 / 232

Fault-Cause-Remedy

166

Instructions for Use Fabius MRI SW 3.n

!!!

(25)

PRESSURE NEGATIVE

Measured P

≤

-5 cmH

(hPa),
or MEAN

≤

-2 cmH

O (hPa).

Check breathing circuit and
ventilator settings.

(8)

PRESSURE SENSOR FAIL

Faulty sensor or pressure not
calibrated.

Call DrägerService or your
local authorized service orga-
nization.

(2)

PRES THRESHOLD LOW

Ventilation parameters were
changed without changing
alarm settings (see page 143).

Push the Auto Set soft key and
check ventilator settings.

(1)

RS232 COM1 FAIL

External monitor cable discon-
nected from External Commu-
nication Port 1.

Check monitor interface cable.

(1)

SPEAKER FAIL

Speaker failed.

Call DrägerService or your
local authorized service orga-
nization.

!!!

(28)

VENTILATOR FAIL

Ventilator not assembled cor-
rectly.

Check diaphragm and close
cover.
Check PEEP/P

MAX

line for

disconnect or leak.
Select Standby Mode and
switch back to the previous
ventilation mode.

(1)

VOLUME ALARMS OFF

Volume alarms disabled by
operator.

Priority Alarm Message

Probable Cause

Remedy

Summary of Contents for Fabius









































































































































































































































Search results

Summary of Contents for Fabius

Reviews:

Dräger Fabius, Instructions For Use Manual, Page: 166 / 232

Search results

Summary of Contents for Fabius

Reviews: