manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 152 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 152

Configuration

152

Instructions for Use Fabius MRI SW 3.n

Configuration during Operation

The user can perform O

2

 calibrations and view and 

change certain monitoring settings for the current 
operation while in Volume Control, Pressure Con-
trol, Pressure Support, SIMV/PS, and Man/Spont 
mode.

1

Press the »

Setup

« key while in Volume Control, 

Pressure Control, Pressure Support, SIMV/PS, 
or Man/Spont mode.

z

The Setup window replaces the waveform and 
soft keys for the current ventilator mode.

The following soft key labels appear in the Setup 
window:
– »

Volume Alarms On/Off

«

– »

Auto Set

«

– »

Calibrate O2 Sensor

«

– »

Des Comp On/Off

«

– »

Access Alarm Log

«

– »

Access Alarm Volume

«

There is a 15-second timeout period for any of the 
Setup functions during operation. If no rotary knob 
activity occurs within 15 seconds, the Setup win-
dow is removed and the waveform window is redis-
played. The waveform window can be also be 
displayed by pressing the »

Home

«

 

key.

NOTE

To set default monitoring settings to be used at the 
power-up of each operation, see “Standby Setup 
Screen” on page 140.

566

1

503

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments