manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 64 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 64

Assembly

64

Instructions for Use Fabius MRI SW 3.n

Connecting the Suction System*

The optional suction system for the Fabius MRI 
consists of a suction regulator and a suction bottle 
system. The suction regulator is attached to a 
holder, which is fastened on the side channel on the 
anesthesia device. The suction bottle desired by 
the customer is attached to a separate swivel rail on 
the side channel.

z

Attach the carrier arm of the suction system on 
the side channel on the side of the anesthesia 
device.

1

Mount the suction regulator onto the bracket.

2

Install the bottle assembly in the slide mount on 
the bracket.

z

Prepare the suction system according to the 
Instructions for Use provided with the suction 
system.

Depending on the suction system used:

If AIR or O

2

 is used as the driving gas:

z

Secure the air connection hose of the suction 
system to the air outlet on the gas supply block 
(optional) or directly to the pipeline gas supply.

For vacuum-driven suction:

z

Connect the vacuum hose of the suction system 
directly to the pipeline gas supply.

Check that the suction system is ready for opera-
tion according to the Instructions for Use provided 
with the suction system.

*

optional

WARNING
Risk of equipment damage
The suction system should be used only in 
ManSpont mode or with the Y-piece discon-
nected.

003

1

2

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments