manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 160 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 160

Fault-Cause-Remedy

160

Instructions for Use Fabius MRI SW 3.n

Ventilator Fail State

If the Fabius MRI does not recover from a 
»

VENTILATOR FAIL!!!

« condition:

z

Switch to ManSpont mode by pressing the 
ManSpont key and confirming the mode change 
by pressing the rotary knob.

z

Set the APL valve to MAN position.

z

Adjust the APL pressure limit for the desired 
inspiratory plateau pressure.

z

Press the O

2

 flush button on the Fabius MRI as 

required to sufficiently inflate the breathing bag.

z

Manually ventilate the patient by squeezing the 
breathing bag.

Overriding the Ventilator

In the unlikely event of a fault in which the ventilator 
does not recover, and the user cannot switch to 
manual ventilation mode through the use of the 
ManSpont key and rotary knob, manual ventilation 
is still possible.

z

Locate the ON/OFF switch on the rear panel.

z

Toggle the ON/OFF switch to “off” ( ) and then

z

Toggle the ON/OFF switch back to “on” ( ). 
The ventilator now performs as in ManSpont 
mode.

z

Set the APL valve to MAN position.

WARNING
Risk of patient injury
If the ventilator fails, the anesthesia machine 
switches to the ventilation mode ManSpont. 
Set the APL valve to a correct pressure limit-
ing value and ventilate the patient manually.

NOTE

In the ventilator fail situation, the ventilator piston 
assembly position may not be locked. As a result, 
airway pressure may initially push the piston back 
to its limit stop, increasing the volume of the 
breathing circuit. It may be necessary to press the 
O

2

 flush button again to reinflate the breathing 

bag.

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments