manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 159 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 159

Instructions for Use Fabius MRI SW 3.n

159

Fault-Cause-Remedy

When the battery is completely discharged 
Fabius MRI switches off. As a consequence all indi-
vidual settings, which are not saved in the default 
settings, will be lost.
All pneumatic functions of the Fabius MRI continue 
to be available (APL valve, breathing pressure 
gauge, cylinder and pipeline gauges, fresh gas and 
agent delivery, S-ORC, and total flowmeter). Man-
ual or spontaneous ventilation can be maintained.

When the power supply is recovered and 
Fabius MRI restarted, all ventilation and alarm set-
tings are reset to the saved default settings.

WARNING
When the »BATTERY LOW!!« Caution alarm 
message is first displayed, the ventilator will 
continue to operate for up to an additional 
10 minutes. Then, automatic ventilation is not 
available until AC power is restored.

CAUTION

Never allow the battery to completely discharge. If 
the battery is discharged completely, recharge 
immediately. Do not use the device until the bat-
tery is recharged completely as injury to the 
patient may occur if the battery is unavailable.

WARNING
Danger of patient injury by wrong device set-
tings or patient settings.
Parameter for ventilation or monitoring may 
be set user-specific.
After restart of the device, check the settings 
and adapt them to your patient, if neccessary.

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments