manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 150 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 150

Configuration

150

Instructions for Use Fabius MRI SW 3.n

Date Format

The values that can be selected for the date format 
are »

MM-DD-YY

« or »

DD-MM-YY

«.

Use the procedure described in “Time Format” on 
page 149 to change the date format parameter.

Acoustic Confirmation

The values that can be selected for the acoustic 
confirmation are »

On

« or »

Off

«.

If »

On

« is selected, an acoustic confirmation is 

annunciated every time that the rotary knob is 
pressed.
Use the procedure described in “Time Format” on 
page 149 to change the acoustic confirmation 
parameter.

Alarm Tone Sequence

The values that can be selected for the alarm tone 
sequence are »

Standard

« or »

Dräger

«.

Use the procedure described in “Time Format” on 
page 149 to change the alarm tone sequence 
parameter.

549

550

551

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments