manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 75 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 75

Instructions for Use Fabius MRI SW 3.n

75

Assembly

Auxiliary power outlets

In cases of a blown safety fuse for the auxiliary out-
lets:
– Remedy the fault
– Have the safety fuse replaced by an electrician

WARNING
The auxiliary outlets are not powered by the 
uninterruptible power supply (UPS) in the 
event of a power failure.

WARNING
Risk of electric shock
Connecting equipment to the auxiliary power 
outlets may cause the patient leakage current 
to rise above the permitted values if a protec-
tive earth conductor should fail. The risk of 
electric shock cannot be excluded in such 
cases.

WARNING
Do not connect life-supporting devices to the 
auxiliary power outlets of the anesthesia 
workstation. The auxiliary power outlets are 
not powered by the uninterruptible power sup-
ply (UPS) in the event of a power failure.

WARNING
Risk of increased leakage current
Do not connect HF surgical devices to the 
auxiliary power outlets.

WARNING
Risk of increased leakage current
Additional power adapter outlets must not be 
connected to the auxiliary power outlets.

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments